- Netduino Forums
- → JonnyBoats's Content
JonnyBoats's Content
There have been 70 items by JonnyBoats (Search limited from 26-June 23)
#29372 Design surface like .NET Gadgeteer for Netduino GO?
Posted by
JonnyBoats
on 18 May 2012 - 05:09 PM
in
Netduino Go
Here is a blog post showing how it works.
Has anyone given any thought to having this for Netduino GO?
#18294 Cortex M3 Arduino
Posted by
JonnyBoats
on 21 September 2011 - 03:29 PM
in
General Discussion
http://blogs.msdn.co...ce-project.aspx
#22274 Is this the end of netduino/arduino boards
Posted by
JonnyBoats
on 31 December 2011 - 01:35 PM
in
General Discussion
#20157 Need Project created
Posted by
JonnyBoats
on 03 November 2011 - 01:29 PM
in
General Discussion
Need a project (c#), in breadboard form to include the following:
2 Temperature/Humidity sensors.
1 RFID reader
1 Wifi
1 GPS
1-2 button(s)
1 display 16 x 2
We would all be glad to help you if you re-phrase your question, For example if you stated "I want to use a Netduino and would like to know what GPS, WiFi and Display shields work well with it?" I am sure you would get several well informed answers. As you probably know, shields simply plug into the Netduino (or Arduino for that matter) and generally are able to be stacked on upon another - no breadboard required.
Perhaps you are looking for a solution without any circuit boards? Did you mean you want to use a Netduino mini plugged directly into a breadboard along with other components? Your request is not clear.
Finally you do not state if this is intended as a "one off" project or a pre-production prototype. The reason I ask this is you should consider that there is already a readily available device that has:
RFID reader
Wifi
GPS
button
display
it is called a smartphone. All you would need to add is the two Temperature/Humidity sensors. Are you familiar with the Android Open Accessory Development Kit?
If you would like to discuss this further please send me a private message here on the forum and we can arrange to speak on the phone if you like.
#21453 Use Microframework with AT91SAM7X256
Posted by
JonnyBoats
on 07 December 2011 - 07:19 PM
in
General Discussion
Hi,
i want to use my netduino code on an trinamic eval board. it has a AT91SAM7X256 instead of AT91SAM7X512
I believe your biggest problem would be that the AT91SAM7X256 has 256 Kbytes of flash wile the Netduino has 512K. I wouldn't say absolutely that it is impossible to get the .NET MF into 256K, but it would be a major challenge.
Far better to select a chip with adequate memory.
#21423 Wanted: Breadboard "Flags"
Posted by
JonnyBoats
on 07 December 2011 - 03:53 AM
in
General Discussion
#16859 TI deals
Posted by
JonnyBoats
on 20 August 2011 - 01:32 AM
in
General Discussion
#15100 Punch Bag Data Logging
Posted by
JonnyBoats
on 06 July 2011 - 01:17 AM
in
General Discussion
You can get one for $30 here: http://www.analog.co...ts/product.html
This board runs on 2 AA batteries and logs the data to an SD card. After your workout session you could put the SD card into your Netduino Plus and do whatever with the data.
#18584 Ship monitor
Posted by
JonnyBoats
on 29 September 2011 - 06:00 PM
in
Project Showcase
I have a LeComte NorthEast 38 sloop.
Many boats have expensive batteries,and monitoring them properly can make them last much longer and save a ton of money. Properly maintained (as in a data center) deep cycle batteries can last 10 years. Many boaters consider themselves lucky to get 3-4 years before replacing them.
If you want to do a really good job of battery monitoring consider using Kelvin 4-wire leads (http://en.wikipedia....erminal_sensing )
#22137 Audiomixer
Posted by
JonnyBoats
on 27 December 2011 - 07:26 PM
in
General Discussion
OK, more digging... I found two good candidates, one 129-steps and one 256-steps digital potentiometer at 10kohm for good money.
I think these will work fine. Now how do I control a bunch (5-8) of these with Netduino, can I do that?
http://se.farnell.co...ip14/dp/9758615
http://se.farnell.co...-spi/dp/1578436
/Ken
#30211 Flashing modules via go!bus
Posted by
JonnyBoats
on 05 June 2012 - 02:53 AM
in
Netduino Go
Status update: the basic flashing routine for STM8S modules is working, at this moment in byte mode (*). Now, when the reflashing app for STM32 is available, it can be extended to include flashing of STM8S-based modules, so we can have an unified interface.
(*) Byte mode is the slowest, word and block programming are faster, but a little bit more complex.
Would you be willing to give a status update as well as information on how to get a copy of the flashing routine?
Thanks.
#29972 Flashing modules via go!bus
Posted by
JonnyBoats
on 30 May 2012 - 03:24 AM
in
Netduino Go
#31304 serial port connection PLEASE!!
Posted by
JonnyBoats
on 28 June 2012 - 06:23 PM
in
Netduino Go
Do you have a volt meter or multimeter?
If so, you should measure the voltage present on your motherboard's pins. Most serial interfaces use 12 volts which is too much for a Netduino. Please be careful.
thank you both for your replies. i, too, believe that i will really enjoy using this thing once i get over this first bump.
i have considered buying another device for interfacing, but i seem to be predisposed to doing things the hard way.
on my motherboard there is a 'COM1' rectangular 10 pin (minus one) socket. 5 pins on top, 4 on bottom. like this:
http://vip.asus.com/...SLanguage=en-us
http://www.frontx.com/cpx102_2b.html
i experimented today with pins D0 and D1 on the shield base connected to (what i think are) pins 2 and 3 of this socket. i got some lights and strange characters to come up on the program http://realterm.sourceforge.net/
but i do not know what the pinout is, nor which pins need to be connected, nor how to confirm the connectivity.
once all of that is done, i am confident i can trudge through the rest on my own.
your help is appreciated.
danny
#31284 serial port connection PLEASE!!
Posted by
JonnyBoats
on 28 June 2012 - 02:54 AM
in
Netduino Go
First off, welcome to the Netduino community. Once you get over your initial frustrations I believe you will have lots of fun learning with your Netduino.
If you find that your computer does not have a serial port connector, don't dispair. Their are other options.
In particular there are USB to serial converters that plug into a USB port on your computer. One thing to be careful of though is the voltage. "standard" serial uses 12 volts which is too high for a Netduino.
This cable might work for you as it uses Netduino compatible voltages: https://www.adafruit.com/products/70
Alternatively this might be even better: FTDI friend There is even a full tutorial on how to use it.
#20486 Sample Requests
Posted by
JonnyBoats
on 11 November 2011 - 02:38 PM
in
General Discussion
I am not a Mac person, but I can tell you that having simple routines that allow reliable communication between a microcomputer and a desktop (e.g PC or Mac) is something that virtually everyone struggles with. The key hangup is reliability.
To be useful in the real world communication needs to be resilient; automatically recovering from such things as power failures, cables being unplugged and being plugged in again etc. If that is something you can workout it will be a great service to us all.
I don't know if this helps, but here is a project someone is doing for the Arduino: http://robotgrrl.com...no/matatino.php
#20978 Measure high current and voltage
Posted by
JonnyBoats
on 25 November 2011 - 08:15 PM
in
General Discussion
For others who might be considering measuring voltages in a residential location such as 120V or 240V (still lethal) there is a good "general" model to follow.
A Netduino (or any other micro-controller) is generally designed to operate on 5V or less (3.3V in the case of a Netduino). It is not designed to survive the application of high voltages (think of it this way, if it would kill you, it will kill a Netduino).
The best approach is to keep the high voltage (or current) on a separate board from the Netduino,
There are many Digital Multi-Meters (DMMs) out there which will output their readings on a serial port. The DMMs are designed and tested to be safe and reliable for measuring voltages and currents within their design specification. You can connect such a DMM to a Netduino via the serial interface (you may or may not need a level shifter such as a MAX232 but that is another issue).
Here is a post where someone used a DMM from Radio Shack in conjunction with a computer: http://www.linuxtoys.org/dvm/dvm.html The price they paid for the DMM seems high (old post perhaps?), I know I bought one on sale (different model) for about $30.
#19408 GPS, GRPS and Google Latitude Tracking
Posted by
JonnyBoats
on 19 October 2011 - 02:05 PM
in
General Discussion
Before proceeding it is extremely important to remember the difference between a hobby project and a safety critical device involving life or death. The "gold standard" for being found in an emergency is a EPIRB (and it's little brother, the Personal EPIRB, or PLB that fits in your pocket). These are extremely rugged, waterproof, tested to the highest standards and have long life batteries. Unfortunately one needs to press a button to activate them, so this is probably a "show stopper" for your application.
Another common device with a built in GPS and communication capability is a cellphone or smart phone. In an emergency authorities can easily locate a cellphone provided it is turned on and within range of a tower. It is highly unlikely that you can engineer a solution with similar capabilities at a lower cost than a used cellphone.
As far as a hobby project is concerned, you might want to consider fox hunting, where you simply attach a small transmitter to your son that sends a radio tone for a couple of seconds every minute or two. To locate the transmitter one only needs a simple receiver and a directional antenna. This is how biologists track animals in the wild. See http://www.predatorc...diotracking.htm for details. Newer versions often include a GPS as well. Here is a link where someone did it on the cheap http://www.thefintels.com/aer/frs.htm to find model rockets.
Finally there are commercially available pet tracking devices such as the Garmin Astro.
#14982 Is there a moisture sensor to put in the ground?
Posted by
JonnyBoats
on 04 July 2011 - 02:46 AM
in
General Discussion
Could you get a 1/4 inch audio jack and just stick it into the soil?
last night I was trying to work out a probe that reads the water level in my hydroponic window box. because the feed water is slightly saline, it conducts, so this approach will work great for it.
In my case, I want to read 'full' or 'empty', so I will just have two wires that are stripped at the ends, just above the low level.
I had thought about using resistance wire, with the water level forming a potentiomiter. that would allow a measure of depth.
thanks for the info!
One thing that is not clear from your question is if you are just trying to experiment or learn or if you are looking for a robust solution.
The reason I bring this up is because measuring full and empty with two wires that are stripped is cheap and easy but does not have good long term reliability. The first issue is that when a DC current passes through the probes electrolysis occurs and the wires degrade over time. One can use better probes such as platnum electrodes and use an AC rather than DC current etc.
On the other hand one can purchase for about $5 a MEMS sensor such as is used in washing machines to detect water level which outputs an analog voltage proportional to the water level. They are extremely reliable and will last practically for ever. I have used the ones from Freescale (http://www.freescale...et/MPXV4006.pdf ) for just this purpose. Take a look at the MPxx4006 family.
#14939 Is there a moisture sensor to put in the ground?
Posted by
JonnyBoats
on 02 July 2011 - 01:40 AM
in
General Discussion
JonnyBoats,
Thanks for the insight. So I guess reading the moisture content of something physical is slightly more of a challenge than originally thought. And that's because i can't find a sensor that will do that for me... But really isn't it the same idea as a pentiometer? One prong receiving electricity, another for it to exit, and one in the middle to read what's moving across the other two?
Very similar. It you would like to try a simple experiment you could stick two pieces of metal with wires attached into a pot of dirt. Connect one to the ground on the Netwuino and the second to one of the analog input pins. This second wire should also be connected to a resistor (try 1 MegOhm, value not critical) and the other end of the resistor to +3.3v on the Netduino. This is what is known as a pull-up resistor.
If the soil is bone dry then you should read a voltage of 3.3v (give or take) on the input pin, this is because the input pin is connected to v+ via the resistors and the resistance between the two pieces of metal is essentially infinite.
Now pour some tap water into the pot. The resistance between the two pieces of metal will now become some finite value and the voltage on the input pin will decrease.
If you were to immerse the two pieces of metal into a glass of salt water the resistance should become very low and the voltage on the input pin become close to zero.
The only real problem at this point is that the resistance also depends on the distance between the two pieces of metal in the dirt. If you wiggle the wires anc change the distance the reading will change as well. A "real" probe will be made so that the two pieces are held at a small fixed distance and usually combined into what looks like a single probe. In fact one connection is simply above the other, just like on a headphone plug that you would plug into the audio jack on your PC.
You can now buy a commercial probe if you like, and as with everything else the price will vary depending on who makes it and the required degree of accuracy.
#15002 Is there a moisture sensor to put in the ground?
Posted by
JonnyBoats
on 04 July 2011 - 04:49 PM
in
General Discussion
Currently I'm experimenting on a small scale using a window-box sized system. I'm in the process of building a greenhouse, and hope to automate it as much as possible, which is why I'm experimenting on the cheep now
![]()
For the full thing, I'll be building/buying sensors design for the long-term.
Thanks for the links! I actually have a pair or scrapped washing machines and a dishwasher, that I've been getting parts from as I need them. I'll see if I can find the sensor.
You might enjoy the video in this blog post: Plantduino Greenhouse Cares Of Your Plats While You’re Away In particular note how they use two ordinary nails to sense moisture in the ground.
All the details, parts list, schematic etc can be found at http://revoltlab.com/.
#14899 Is there a moisture sensor to put in the ground?
Posted by
JonnyBoats
on 30 June 2011 - 01:03 PM
in
General Discussion
Basically the way it works is that the resistance of wet soil is lower than that of dry soil. You could either make your own probe or hack one of the cheap probes from a garden supply shop.
#20156 Arm DSO Nano and family
Posted by
JonnyBoats
on 03 November 2011 - 01:14 PM
in
General Discussion
#16013 Sweet deal for capacitive touch interface
Posted by
JonnyBoats
on 29 July 2011 - 12:42 AM
in
General Discussion
I just got around to fooling with this and it isn't clear (to me) how to interface this to the Netduino. The video mentions interfacing the the USB but there are no details. I suppose I can look at their SDK but I believe it is C++ and would require some port to Netduino.
Has anyone actually interfaced this to a Netduino?
The easiest way to interface the TI chip to the Netduino is via the TTL level serial port, both boards have them.
#21619 Current State of features
Posted by
JonnyBoats
on 12 December 2011 - 02:10 PM
in
General Discussion
The issue is that, if switching off the whole board, the Netduino wouldn't be able to wake up on time for the UI to flow nicely.
Have you measured the total time for your application to start from a cold boot? I am curious as I would have thought that it would be possible to get that into an "acceptable" range.
As for handling the keyboard and display, why not use a really low power chip (like perhaps the $4.30 TI MSP430 board) to handle that and cause the Netduino to boot as required (like when a key is pressed).
#21179 Problems with USB Port in WIndows 7
Posted by
JonnyBoats
on 30 November 2011 - 06:08 PM
in
Netduino Plus 2 (and Netduino Plus 1)
Hi Mikeo2721,
I wear out a USB port on my computers just about every year. They're rated for thousands of insertion cycles--but it's amazing how many times I unplug/plug things around here testing engineering samples, etc.
Anyway, let's make sure we get you up and running...
Chris
Chris, If you wear out a USB port on a motherboard that can be an expensive fix ;-)
Have you considered using a USB extension cable (male on one end, female on the other) and leaving it plugged into the PC continuously? That way it would be the extension cable that would wear out, not the socket on the PC.
- Netduino Forums
- → JonnyBoats's Content
- Privacy Policy