Ok.. then for now I will be updating to 4.2 again.
- Netduino Forums
- → zemuss's Content
zemuss's Content
There have been 69 items by zemuss (Search limited from 07-May 23)
#46596 .net Micro framework 4.3 question
Posted by zemuss on 03 March 2013 - 11:04 PM in Netduino Go
#46564 .net Micro framework 4.3 question
Posted by zemuss on 03 March 2013 - 01:55 AM in Netduino Go
Hi everyone,
Is there a firmware update to go along with .net 4.3?
Will the latest 4.2.X firmware work?
"Z"
#46562 DS18B20 Wiring help
Posted by zemuss on 03 March 2013 - 01:43 AM in Netduino Go
I need a bit of help here.
The DS18B20 that I bought came with a RED, White and Black wire. Can anyone confirm the connections please?
RED =
White =
Black = GND
#46452 SD Card Module Update
Posted by zemuss on 01 March 2013 - 01:42 AM in Netduino Go
Never mind I just did some reading and it isn't a purchase. Any ETA on the GoBus?
Need any beta testers?
#46426 SD Card Module Update
Posted by zemuss on 28 February 2013 - 07:58 PM in Netduino Go
Did the SD module start shipping? I am unable to find it...
#45601 Salt Water Aquarium Controller
Posted by zemuss on 16 February 2013 - 04:40 AM in Netduino Go
Haven't gotten that far. These are just mock ups.
Waiting for the Temp Sensors.
#45512 Mosfet IRF540 v2.0
Posted by zemuss on 14 February 2013 - 04:48 PM in Netduino Go
I think I will go with the Meanwell Drivers which are used for high powered LEDS and get a constant power supply.
Thanks for the help everyone its much appreciated.
#45479 Mosfet IRF540 v2.0
Posted by zemuss on 13 February 2013 - 11:02 PM in Netduino Go
http://www.emartee.c...ton IRF540 V2.0
Does anyone know if the netduino can control this device?
Anyone using it for LEDs as a driver?
#45473 The GoBus Upgrade
Posted by zemuss on 13 February 2013 - 09:44 PM in Netduino Go
When will the Ethernet module release?
#45469 Salt Water Aquarium Controller
Posted by zemuss on 13 February 2013 - 09:28 PM in Netduino Go
#45460 Salt Water Aquarium Controller
Posted by zemuss on 13 February 2013 - 07:56 PM in Netduino Go
Yes I think I will create a digital read out, however if I go that route then the gauges are not required.
I am going to make another mock up with digital and see which I like.
#45443 Salt Water Aquarium Controller
Posted by zemuss on 13 February 2013 - 04:42 PM in Netduino Go
#45338 Salt Water Aquarium Controller
Posted by zemuss on 11 February 2013 - 09:54 PM in Netduino Go
I will take some screen shots of the GUI I am creating.
Do you know any free gauge controls that I can use?
#45328 Ethernet Module Update
Posted by zemuss on 11 February 2013 - 06:32 PM in Netduino Go
Any update on release?
#45324 Salt Water Aquarium Controller
Posted by zemuss on 11 February 2013 - 06:05 PM in Netduino Go
I am looking for some feed back on the Temperature sensor.
If I hook that directly to the shield base module should I use some type of breakout board? Meaning use a three prong connector instead of hooking it directly to the shield base board?
"Z"
#45323 Salt Water Aquarium Controller
Posted by zemuss on 11 February 2013 - 06:03 PM in Netduino Go
Ok I have done a ton of research and it is time to start my project.
The controller will be based on the NetDuino Go board and the project will start off very basic with a temperature sensor for display tank and sump temperature sensor.
Temperature sensor will be: https://www.sparkfun.../products/11050
Future plans:
Ph sensor from Atlas-Scientific: http://www.atlas-sci...its/ph-kit.html
Light Controller for LED lighting system.
#45321 N+(2) Aquarium Controller
Posted by zemuss on 11 February 2013 - 05:25 PM in Project Showcase
Thank Jeittreim.
Question do I need another module to run the probe you linked?
#45317 Starting My Aquarium Controller (Need Help)
Posted by zemuss on 11 February 2013 - 03:46 PM in Netduino Go
So now I need to figure out which temp sensor to use.
The aquarium it will be on is Salt Water and I need a sensor that will not corrode. Any suggestions?
#45315 N+(2) Aquarium Controller
Posted by zemuss on 11 February 2013 - 03:04 PM in Project Showcase
HO7R0d which temp probe did you use?
I think I will use this one: http://littlebirdele...rproof-ds18b20. Non-metal casing. Any thoughts?
#45281 N+(2) Aquarium Controller
Posted by zemuss on 11 February 2013 - 03:54 AM in Project Showcase
http://adafruit.com/products/381 <-- would this temp sensor work on a Salt water tank?
#45280 Starting My Aquarium Controller (Need Help)
Posted by zemuss on 11 February 2013 - 03:22 AM in Netduino Go
Can someone help me get this off the ground?
What should I do first? I am lost as what steps to follow.
Basically I would like to have it interface with my computer and use a windows application to display the Temp / PH and control the lights at a later point.
#45279 N+(2) Aquarium Controller
Posted by zemuss on 11 February 2013 - 03:19 AM in Project Showcase
I need a little help guys.
What should I try first?
I would like to start putting the controller together.
#41562 N+(2) Aquarium Controller
Posted by zemuss on 14 December 2012 - 04:01 PM in Project Showcase
#41167 N+(2) Aquarium Controller
Posted by zemuss on 07 December 2012 - 06:22 PM in Project Showcase
#41164 N+(2) Aquarium Controller
Posted by zemuss on 07 December 2012 - 06:09 PM in Project Showcase
- Netduino Forums
- → zemuss's Content
- Privacy Policy