Netduino home hardware projects downloads community

Jump to content


The Netduino forums have been replaced by new forums at community.wildernesslabs.co. This site has been preserved for archival purposes only and the ability to make new accounts or posts has been turned off.

piwi

Member Since 18 Jul 2011
Offline Last Active May 18 2021 06:14 PM
-----

#59871 Windows on Devices? When?

Posted by piwi on 24 August 2014 - 06:08 PM

Linux is no different...

For me IoT = STM32F4xx + NETMF

Does everything I need...

 

right on Juzzer ... I can only agree ... and now with the 411 coming, even the better ... 

 

The STMF32F429 is, once getting it to work and as far as I can say for the moment, pretty fast but power hungry as well ...

 

 .. but than again it is not really needed (fot IoT) to have the LCD power on board, there are other ways to display output ...

 

Can't barely wait for the discovery kit coming out in the fourth quarter ... maybe an idea for your next workshop (the 411) ...




#59849 .net MF on 32F429IDISCOVERY

Posted by piwi on 21 August 2014 - 11:44 PM

wooohaaa .... running ... don't ask me why ... probably when I power down the pc the next time it won't work .... this was an adventure ... I even managed to give the device a new usb name ... of course after that I had a breaking issue so I went back to the st-link utility and set the name bytes to hex 00 and the original usb name came up again. Back to VS, started deploying only to figure out you can not mixed netmf versions, so had to uninstall 4.3.1.0 and install 4.3.0.0 since the ST is on that and voila there we go it deployed and ran almost faster then I could blink but instead the LEDs did so we have a nice running a little blinky led and empty screen program on a not so stable disco board:

 

Blinky_zps6c15dec5.jpg




#59839 .net MF on 32F429IDISCOVERY

Posted by piwi on 21 August 2014 - 07:36 PM

well so far so good ....

 

20140821_212518_zpsc4f8c054.jpg




#58959 Spark Core (TI CC3000) Porting for Super WiFI Mini?

Posted by piwi on 30 June 2014 - 12:25 PM

.... maybe there will be an alternative (STM32F427, Wifi, 4.3) ....

 

.... interrested ? ....




#52882 Spark Core (TI CC3000) Porting for Super WiFI Mini?

Posted by piwi on 24 September 2013 - 07:30 PM

with a smart config via an iPad4 ...

Example App:driver version 5.14.7.13MAC 08:00:28:01:6F:DBSP: 0.6.1.2401Smart config DONEDONEIP:192.168.39.18

and look ma without any resistors ....

The thread '<No Name>' (0x2) has exited with code 0 (0x0).CC3000 Internet Time ExampleSending - Simple Link StartSend 4000 startingResponse Received -- Simple Link Start ConfirmedSetting Event MaskSend 0008 startingResponse Received -- Event Mask confirmedRequesting SP VersionSend 0207 startingResponse Received -- SP Version is 0.6.1.24Requesting Buffer SizeSend 400B startingResponse Received -- Buffer Available: 6, Size: 1500Configuring DHCPSend 2001 starting

Direct wiring a CC3000 Boost to a cerbuino with 4.3 ... sorry but my n+ does not do 4.3 ....

 

why the DHCP does not work .... no clou but there is always something ...




#51691 Spark Core (TI CC3000) Porting for Super WiFI Mini?

Posted by piwi on 25 July 2013 - 09:58 PM

..... well finally there is some positive news for and from me !!!

 

Since my second boost did not work either, I got me an FRAM board (FR5739) and the CC3000EM, downloaded the sensor app to it, did some smartconfig from an ipad to an open AP. Did not work, but after stopping the ipad app it began to start to burn the leds 2, then 3 and finally number 4 .... aha ... it does work ... without any patches made. Now launching the PC sensor app turned into a nice window where the acceleration, temp and vcc were displayed just nicely and tilting the board was reflected in the planet as well, that looked quit cool compared to the bummers I had with the boost stuff.

 

Posted Image

The FR5739 board with six leds burning communicating over sockets against

Posted Image

Cool sensor app.

 

Now the boost with the stellaris keeps freezing in the smartconfig section after issueing command 01 the led start with blinking red and stays there, no matter what smartconfig app I run from (tried pc and ios) stays blinking and no change in my ap's dhcp clients.

 

Hyperterminal is reporting 5.14.7.13 ....

 

Next will be to connect the CC3000EM to the netduino and get it to work as well .... at least now we've got a working model with sockets ...

 

 

@Hanzibal: cool looking board. Success with it...




home    hardware    projects    downloads    community    where to buy    contact Copyright © 2016 Wilderness Labs Inc.  |  Legal   |   CC BY-SA
This webpage is licensed under a Creative Commons Attribution-ShareAlike License.