@CW2... Thank you very very much for putting this together!!!!
Now if we can get someone to write some managed CAN drivers.......
-Matt
![]() |
  | |||||||||||||
![]() |
|
![]() |
||||||||||||
The Netduino forums have been replaced by new forums at community.wildernesslabs.co.
This site has been preserved for archival purposes only
and the ability to make new accounts or posts has been turned off.
zeroaviation's ContentThere have been 16 items by zeroaviation (Search limited from 17-June 23) #58021 Netduino 2 Firmware v4.3.1 with GCC support
@CW2... Thank you very very much for putting this together!!!!
Now if we can get someone to write some managed CAN drivers.......
-Matt #59833 .net MF on 32F429IDISCOVERY
Could you share what you guys have?
Cheers, -Matt #59887 .net MF on 32F429IDISCOVERY
@piwi
Are you running the STM port?
Cheers, -Matt #59888 .net MF on 32F429IDISCOVERY
Double post. #59801 .net MF on 32F429IDISCOVERY
ST has a setup already out there http://www.st.com/we.../tools/PF260087
However, its closed source :/ I hope either they release the source, or someone builds their own.
Cheers, -Matt #54469 Does any one needs CAN Bus on Netduino?
Subscribing to this thread! I'm highly, highly interested in using CAN on netduino. SPI-> CAN Interfaces are too slow and in my opinion buggy when using networks that are more than 70% utilization.
Looking forward to a release! #54808 .Net MF 4.3 Firmware for Netduino Plus 2 with CAN/SDIO/RTC/CRC/RND [Uploaded]...
Is there a donate button somewhere? #54571 .Net MF 4.3 Firmware for Netduino Plus 2 with CAN/SDIO/RTC/CRC/RND [Uploaded]...
Do you plan to release it? (At least the CAN part)
-Matt #57634 "JIT" has been done for .Net Micro Framework 4.3.1
He sadly hasn't shared any code written in the past. Only tried to sale it #60856 DTMF with netduino plus 2
#59421 CANBUS / MCP2515 drivers?
Has been working good for me. Though, its throughput is slow, I belive its the speed of the .NETMF that makes it this way. :/
I would pay someone to write native drivers for CAN BUS on the netduino. Just sayin.
Cheers, -Matt #54492 Netduino 2 JTAG header type (size) and JTAG device
Hi,
I want to start learning native development. I figured what better to learn it on than the netduino!
I seen some posts on here about soldering in a JTAG header. But looking at the header it seems to be a non standard type.
Can someone help me locate a header I can solder in? Maybe a mouser or digikey part #?
Also, whats the popular JTAG debugging device? Does Secret Labs have a fav?
Thanks! -Matt #60408 Tic Toc
Open source right?!!? #54509 Netduino 2 JTAG header type (size) and JTAG device
Thank you guys very much!!!
I'm going to get the GoPorts and ST-LINK/V2.
Thanks again!
-Matt #59509 Opinions needed on CAN interface project
In my opinion. With the netduino your best options is to use a MCP2515 SPI=> CAN (which is what the shield is). I really really really wish someone would write and post up a Native CAN Driver for the netduino. I would PAY someone to do it out of my own pocket.
The bad thing about the SPI=>CAN is that it is slow, so for doing fast automotive module programming, it wont cut the cheese... However, if your just reading data, or querying OBD then you wont have a problem.
Cheers, -Matt #60427 3-4 inch Graphic TFT for Netduino
Gents (and maybe ladies),
I'm seeking a TFT display for a project I am working on. It appears that there are not available drivers for a TFT in the 3-4 inch range. (I look at Netduino helpers, and did a search here)
Does anyone have a recommendation for a TFT display and driver? No preference on interface (parallel or serial) touch would be nice.
Cheers, -Matt
| ||||||||||||||
![]() |
||||||||||||||
![]() |
|
![]() |
||||||||||||
![]() |
This webpage is licensed under a Creative Commons Attribution-ShareAlike License. | ![]() |
||||||||||||
![]() |