What I can definitely see after investigation playing with stepping motor, there are delays in either changing status on pin or code interpretation
- Netduino Forums
- → eplaksienko's Content
eplaksienko's Content
There have been 107 items by eplaksienko (Search limited from 25-September 23)
#47291 Wrong numbers when working with sonar sensor
Posted by eplaksienko on 17 March 2013 - 02:16 PM in Netduino Go
#47359 Wrong numbers when working with sonar sensor
Posted by eplaksienko on 18 March 2013 - 10:27 PM in Netduino Go
I was able to find delay I see progression, but it's definitely not enough
#47253 Wrong numbers when working with sonar sensor
Posted by eplaksienko on 15 March 2013 - 11:16 PM in Netduino Go
I am still working on shaman-ning it, I am almost there, If folks around will not find scientific solution, hopefully I would be able to give different delays and conversions
#47336 Wrong numbers when working with sonar sensor
Posted by eplaksienko on 18 March 2013 - 05:28 PM in Netduino Go
I am working right now with idea to figure out what's the real delay between NGO and SB
I believe if this one solved we almost there
#47846 Wrong numbers when working with sonar sensor
Posted by eplaksienko on 31 March 2013 - 05:41 PM in Netduino Go
Chris, I see incremental number while moving things further and excremental when going closer, but I can not tune exact number, I didn't yet figured out dependencies experimentally, but the same sonic sensor works great and gives exact calculated numbers with Arduino
#47188 Wrong numbers when working with sonar sensor
Posted by eplaksienko on 14 March 2013 - 02:25 PM in Netduino Go
Chris 1 question related to SB
I try to play with sonic distance sensor, one of the guys shared the code http://forums.netdui...ic-rangefinder/
I didn't try it with Netduino, but combination of NGO and SB doesn't give correct numbers, is there any specific delays or other could be the reson
PS: I tried the module with Arduino it works
#47698 Wrong numbers when working with sonar sensor
Posted by eplaksienko on 28 March 2013 - 07:36 PM in Netduino Go
No, was busy with other staff, I think Secret Labs staff help would be very useful, since it's 99.99% lateness issue, not sure if it because NGO connectivity or SB itself or both. But we should be able to get from them numbers to make calculations better
#52859 World Maker Faire New York 2013
Posted by eplaksienko on 22 September 2013 - 04:16 PM in General Discussion
Gutworks, any news about ngo? anything new there or the same abandoned project?
#48985 TristatePort through exception while construct via SB
Posted by eplaksienko on 03 May 2013 - 02:12 PM in Netduino Go
Thx Lunddahl, but no solution there yet
#48930 TristatePort through exception while construct via SB
Posted by eplaksienko on 02 May 2013 - 02:26 AM in Netduino Go
Hi!
TristatePort throw exception while construct via SB
here the code
#49453 TristatePort Issue
Posted by eplaksienko on 15 May 2013 - 01:35 AM in Netduino Go
Chris I personally first tried to dispose OutputPort with the exception, then I tried to use TristatePort, and get the same kind of unknown exception. I am just trying to play with CharliePlexing
#48984 TristatePort Issue
Posted by eplaksienko on 03 May 2013 - 02:12 PM in Netduino Go
Chris any news about it?
#48991 TristatePort Issue
Posted by eplaksienko on 03 May 2013 - 06:10 PM in Netduino Go
Chris, is it related to the issue with can not dispose OutportPort?
#50441 TristatePort Issue
Posted by eplaksienko on 12 June 2013 - 02:25 PM in Netduino Go
Chris, any updates on this issue?
#47714 Toolbox HBridge with SB
Posted by eplaksienko on 29 March 2013 - 02:30 AM in Netduino Go
Hi!
Anybody has experience SB with DFRobot L298P using HBridge, no errors motor doesn't rotate
Here the code
#47723 Toolbox HBridge with SB
Posted by eplaksienko on 29 March 2013 - 12:23 PM in Netduino Go
Thanks Stefan, I found the solution from absolutely different angle , but without your tip I wouldn't get it, it's somehow different MS, no PWM/PLL switch, and what happened it was different pins I will post later today pic of the shield, but it was shipped by robotshop.com in dfrobot wrappinf with df robot logo on it
Actually is there class to control stepper with it?
#48411 The project type is not supported by this installation
Posted by eplaksienko on 15 April 2013 - 05:31 PM in Netduino Go
Chris, actually I started workshop with my son and several his friends based on NGO, and one of them had similar problem, got solved after re-installation of VS C# and of course all libs and templates both Netmf and Secret Labs
#47433 ShieldBase Power Bug?
Posted by eplaksienko on 21 March 2013 - 02:01 AM in Netduino Go
I could get to you Monday or Tuesday
Actually 1 sec Sleep is not enough, 3 sec is sure number
#47417 ShieldBase Power Bug?
Posted by eplaksienko on 20 March 2013 - 05:22 PM in Netduino Go
Chris If you can not reproduce it in lab, I work in NY I could bring mine for investigation
#47427 ShieldBase Power Bug?
Posted by eplaksienko on 20 March 2013 - 10:40 PM in Netduino Go
#47415 ShieldBase Power Bug?
Posted by eplaksienko on 20 March 2013 - 02:38 PM in Netduino Go
Have the same issue, cry
#48769 Shield base pins reassignment
Posted by eplaksienko on 26 April 2013 - 03:36 PM in Netduino Go
Thread.Sleep(5000);
#48761 Shield base pins reassignment
Posted by eplaksienko on 26 April 2013 - 02:18 PM in Netduino Go
Chris, I get exception on dispose
#48690 Shield base pins reassignment
Posted by eplaksienko on 24 April 2013 - 01:50 PM in Netduino Go
Thanks Chris
Actually, about disposal, what the quickest way to do it in NETMF? I am C++ person and C# and Java behavior make me always puzzled about it
#48661 Shield base pins reassignment
Posted by eplaksienko on 23 April 2013 - 03:47 PM in Netduino Go
Question What happens if I open some D pin on shield base as output, then in some period of time reassign it as input?
Is it going to work? Does it require specific actions?
Thanks
- Netduino Forums
- → eplaksienko's Content
- Privacy Policy