Hi!
Does it exist Analog Output for SB?
eplaksienko's Content
There have been 107 items by eplaksienko (Search limited from 01-July 24)
#47847 Analog Output for SB
Posted by
on 31 March 2013 - 05:44 PM
in
Netduino Go
#47852 Analog Output for SB
Posted by
on 31 March 2013 - 08:21 PM
in
Netduino Go
Thx Already have solution with PWM
#47888 Analog Output for SB
Posted by
on 01 April 2013 - 07:39 PM
in
Netduino Go
Thx guys, It was just a little bit confusing no having yet analog output for SB
#48329 Building custom go!bus modules for Netduino Go
Posted by
on 12 April 2013 - 02:07 PM
in
Netduino Go
I am always convinced myself recall what I studied 20 years ago and start developing my own modules 
Will start from Sonic Range Finder
#49359 Continuous Rotation Servo on the Shield Base controlled with Potentiometer
Posted by
on 12 May 2013 - 02:23 AM
in
Netduino Go
I looks like have terrible problem with all this SB and servo, it just makes some just initial move, then stops like nothing happens
Any idea why, I tried all solutions above and what I can imagine, the same problem
#49395 Continuous Rotation Servo on the Shield Base controlled with Potentiometer
Posted by
on 13 May 2013 - 06:54 PM
in
Netduino Go
I solved it, some reason servo I think was rusty inside, I put head on it, turned several times and now it's ok
#47863 Current state of the Go
Posted by
on 01 April 2013 - 01:01 AM
in
Netduino Go
Chris, amateur question , Is it possible or will be possible to make work NGO and SB independently, something like for example RPI and Alamode
#47732 Current state of the Go
Posted by
on 29 March 2013 - 05:40 PM
in
Netduino Go
Arron, I know it's not going to be the same as N+2 or Arduino, but currently what I see is just unacceptable, basically I can not use Stepper motor and sonic range finder, I think this could be tuned, or may be something similar to RPI to have separate control on main board and SB
#47696 Current state of the Go
Posted by
on 28 March 2013 - 07:34 PM
in
Netduino Go
I absolutely agree with Troll, at least Secret Labs could finish Gadgeteer extention to be able to use GHI modules, and of course should be found solution with SB working much slow then Netduino or Arduino, I think those 2 things are the most critical from my point of view
#47743 Current state of the Go
Posted by
on 30 March 2013 - 01:52 AM
in
Netduino Go
There is no point in beta if no release in mind , I am not talking about high high performance, but for example 4-5 quicker would be enough for Stepper and 10 for sonic range finder.
Actually, isn't it SB already works via SPI?
#47753 Current state of the Go
Posted by
on 30 March 2013 - 01:10 PM
in
Netduino Go
Hopefully this will move somewhere
#46022 Early "Getting Started with Netduino Go" software and instructions
Posted by
on 22 February 2013 - 01:31 AM
in
Netduino Go
Gutworks I tryed, it was obvious if double it's meant under 1, but I don't see any affect in brightness
#46075 Early "Getting Started with Netduino Go" software and instructions
Posted by
on 22 February 2013 - 02:31 PM
in
Netduino Go
Thx, some reason I tried the same before your reply and it didn't work, suddenly yesterdays night it started to work
#46016 Early "Getting Started with Netduino Go" software and instructions
Posted by
on 22 February 2013 - 12:15 AM
in
Netduino Go
Chris, I am trying to change rgb led module brightness, with no success. I see I have to put double value, but I have such a feeling I am not correct with the range
#52670 Ethernet Module Update
Posted by
on 09 September 2013 - 05:45 PM
in
Netduino Go
Chris is it available list? http://www.mouser.co...Nx2gR1uMV10Cqp6
#52692 Ethernet Module Update
Posted by
on 10 September 2013 - 11:24 PM
in
Netduino Go
half a year..... it doesn't sound like some specific date, sounds like project abandoned
#50812 Ethernet Module Update
Posted by
on 25 June 2013 - 08:28 PM
in
Netduino Go
If secret labs at least issued their Go to Gadgeteer module and make available all 8 ports multiple SB I would consider at least there is any change for good, but looks like it's dead
#54490 Ethernet Module Update
Posted by
on 05 December 2013 - 03:52 PM
in
Netduino Go
Chris, you guys very behind the schedule, I started to develop step motor and distance sensor modules but I stopped because future of the project is uncertain
#54480 Ethernet Module Update
Posted by
on 05 December 2013 - 03:01 AM
in
Netduino Go
I moved to GHI by now and research udoo
#48228 Ethernet Module Update
Posted by
on 09 April 2013 - 08:52 PM
in
Netduino Go
And also since it will be more modules in future to make it for example 16 port?
#48227 Ethernet Module Update
Posted by
on 09 April 2013 - 08:50 PM
in
Netduino Go
Chris, may me it has sense to redesign NGO itself, just make it onboard instead of creating module?
#48237 Ethernet Module Update
Posted by
on 10 April 2013 - 02:34 AM
in
Netduino Go
Ulrik, I 99.99% agree with you but particularly ethernet onboard I think could be great +, again this is IMHO
#49854 Ethernet Module Update
Posted by
on 23 May 2013 - 07:29 PM
in
Netduino Go
Did anybody tried GHI ethernet module?
#49875 Ethernet Module Update
Posted by
on 23 May 2013 - 11:21 PM
in
Netduino Go
Looks like this module is SPI
#52625 How fast can the shield base go?
Posted by
on 07 September 2013 - 05:25 AM
in
Netduino Go
I stack with the same problem, solution is to develop own module, which is look like not going to be soon, may be loooooooooong expected bus 1.5 will help, but hope is little
