molillo - Viewing Profile: Posts - Netduino Forums
   
Netduino home hardware projects downloads community

Jump to content

  2. → Viewing Profile: Posts: molillo

The Netduino forums have been replaced by new forums at community.wildernesslabs.co. This site has been preserved for archival purposes only and the ability to make new accounts or posts has been turned off.

molillo

Member Since 09 Jul 2012
Offline Last Active Jan 21 2013 06:39 PM
-----

Posts I've Made

In Topic: My NetDuino not response to MFDeploy

11 July 2012 - 06:32 PM

I am grateful for your invaluable help! Last night I installed version 4.1 on another PC, and perfect, I pinged and deploy the firmware properly. I installed the Microsoft environment, and I can debug an application correctly. Looking in my PC where USB was the problem, I found an application on my PC which modified the boot.ini for the initiation of various systems, and has long wanted to solve. There was an error, and I've spent all day trying to repair the Boot Sector of my PC. So I have not answered before, and I needed my PC for work. Anecdotally, I'm writing with my PC, and the other PC I will focus on developing software in NetDuino Plus. When I get USB fix the problem in my PC, I will tell in this forum. Thanks for everything. Sincerely,

In Topic: My NetDuino not response to MFDeploy

10 July 2012 - 07:07 AM

I am very grateful to have your help. Currently, I just want to install the firmware V4.1.0.6. I'm back doing the following steps with tutorials: Netduino connect via USB and clean the device connecting 3.3 and gold pad USB disconnect and connect again, my system detects serial port COM39 Run SAM-BA 2.11 and Connect "Boot from Flash GPNVM2" - Execute "Enable Flash access" - Execute Open File (TinyBooterDecompressor.bin - NetduinoPlus_TinyBooterDecompressor v4.1.0.6.zip) Send File "Sending file to target" Lock it ¿? - NO I launch "Compare sat file with memory" and request: "Send file & Memory content area (address: 0x100000, size: 42064 bytes) match exactly! I close the application and disconnect Netduino. Netduino connect again and get a USB device called Netduino: USB \ VID_22B1 & PID_1000 \ 5 & 27736F70 & 0 & 2 Controller: "Secret Labs LLC" Version: 1.0.0.0 For now, if that is the correct driver for the USB device, I think everything is going well. I start C: \ Program Files \ Microsoft. NET Micro Framework \ v4.1 \ Tools \ MFDeploy.exe Select USB and NetduinoPlus_NetduinoPlus and you see the problem: PING: not responding. I have to disconnect the USB to respond MFDeploy "Pinging ... Failed: No response from device". Deploy: Does not work. Device does not respond! I disconnected and connected USB Netduino and hold SW1 held on startup, etc, etc ... and I can not. I think the USB driver is NOT suitable for the bootloader, and I must reinstall other more advanced USB driver. Thanks for your help, and I'm sorry I wrote so much text. I have replace the USB drivers: (C:\Archivos de programa\Secret Labs\Netduino SDK\Drivers) USB\VID_22B1&PID_1000\5&27736F70&0&1 Controller: Secret Labs LLC 10/04/2012 V4.2.0.0 And don´t work ...

  1. Netduino Forums
  2. → Viewing Profile: Posts: molillo
  3. Privacy Policy
home    hardware    projects    downloads    community    where to buy    contact Copyright © 2016 Wilderness Labs Inc.  |  Legal   |   CC BY-SA
This webpage is licensed under a Creative Commons Attribution-ShareAlike License.