Netduino home hardware projects downloads community

Jump to content


The Netduino forums have been replaced by new forums at community.wildernesslabs.co. This site has been preserved for archival purposes only and the ability to make new accounts or posts has been turned off.
Photo

Netduino crystal Oscillator


Best Answer ziggurat29, 24 March 2013 - 01:37 AM

my schematic shows 25mhz, are you talking about the older Atmel based board?
The NP2 seems to use one like this:

http://www.mouser.co...9c3qg%2b5z6ARQ=

Have you made your boards already?  could you not use something like this with a similar pad style

http://www.mouser.co.../cqvVt1bBdEIS8=

or this, much cheaper but different pad style

http://www.mouser.co...4KvT7BqaZN1LO8=

Go to the full post


  • Please log in to reply
5 replies to this topic

#1 Nym

Nym

    Member

  • Members
  • PipPip
  • 20 posts

Posted 23 March 2013 - 10:25 PM

Hi community,

 

I'm crashing my head against the wall to select the correct crystal oscillator from Netduino design. I designed my custom Pcb board derived from Netduino and then I need to buy a crystall oscillator. Does anyone has vendor URL at hand where I can order the 18.432 Mhz crystall oscillator in US? I google up and there are too many different configurations for this type of crystal and variety of manufactures then things start to be confusing for me.

 

Thanks in advance for any help

 

Nym.



#2 NooM

NooM

    Advanced Member

  • Members
  • PipPipPip
  • 490 posts
  • LocationAustria

Posted 24 March 2013 - 01:23 AM

isent it 25mhz ?



#3 ziggurat29

ziggurat29

    Advanced Member

  • Members
  • PipPipPip
  • 244 posts

Posted 24 March 2013 - 01:37 AM   Best Answer

my schematic shows 25mhz, are you talking about the older Atmel based board?
The NP2 seems to use one like this:

http://www.mouser.co...9c3qg%2b5z6ARQ=

Have you made your boards already?  could you not use something like this with a similar pad style

http://www.mouser.co.../cqvVt1bBdEIS8=

or this, much cheaper but different pad style

http://www.mouser.co...4KvT7BqaZN1LO8=



#4 Nym

Nym

    Member

  • Members
  • PipPip
  • 20 posts

Posted 24 March 2013 - 03:47 PM

Thanks NooM and ziggurat29 for your help here, yes I'm using the old Netduino 1 schematics version. I sent my board to be manufactured without double checking the crystal thing and discovered that I selected through hole style versus SMD which would make life easier to find appropriate crystal but harder to solder on it. Since I cannot get the benefit of the pad configurations, darn!!!, I chose 3 different packages to be sent from mouser. They were derived from above hints so I greatly appreciate the help from the community.



#5 CW2

CW2

    Advanced Member

  • Members
  • PipPipPip
  • 1592 posts
  • LocationCzech Republic

Posted 24 March 2013 - 04:23 PM

The crystal is ABM7-18.432MHZ-10-D2Y-T by Abracon (ABM7 series datasheet), in single quantities available at Digikey (535-9841-1-ND), Mouser (815-ABM7-18.4-D2Y-T).

#6 Nym

Nym

    Member

  • Members
  • PipPip
  • 20 posts

Posted 04 April 2013 - 06:53 PM

Got it.already ordered them and running up :). Thanks






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

home    hardware    projects    downloads    community    where to buy    contact Copyright © 2016 Wilderness Labs Inc.  |  Legal   |   CC BY-SA
This webpage is licensed under a Creative Commons Attribution-ShareAlike License.