Netduino home hardware projects downloads community

Jump to content


The Netduino forums have been replaced by new forums at community.wildernesslabs.co. This site has been preserved for archival purposes only and the ability to make new accounts or posts has been turned off.

bramVD

Member Since 02 Jul 2012
Offline Last Active Jun 03 2013 03:50 PM
-----

Posts I've Made

In Topic: Netduino doen't run or debug

11 January 2013 - 04:46 PM

AH, lol. didn't know that.
always thought is was backward compatible.
 
its posible to go back to the 4.1 framework  if your on the 4.2?
 
 
no longer necessary.. fixed it.
 
i searched for the MicroLiquidCrystal  source code, and found it.
used the 2 classes necessary for the LCD. and imported those into the project.
 
and it works fine now :)

In Topic: Netduino doen't run or debug

11 January 2013 - 04:31 PM

Oke, did the Reboot CLR and Ping, this is the result:

 

Configuration version != versionAssembly: MicroLiquidCrystal (1.1.0.0)Found debugger!Create TS. Loading start at 142afc, end 1583e0   Assembly: mscorlib (4.2.0.0)   Assembly: Microsoft.SPOT.Native (4.2.0.0)   Assembly: Microsoft.SPOT.Hardware (4.2.0.0)   Assembly: Microsoft.SPOT.Hardware.SerialPort (4.2.0.0)   Assembly: Microsoft.SPOT.IO (4.2.0.0)   Assembly: System.IO (4.2.0.0)   Assembly: Microsoft.SPOT.Hardware.PWM (4.2.0.1) needs assembly 'mscorlib' (4.1.2821.0)   Assembly: SecretLabs.NETMF.Diagnostics (4.2.0.0)Assembly: MicroLiquidCrystal (1.1.0.0)   Assembly: SecretLabs.NETMF.IO (4.2.0.0) needs assembly 'Microsoft.SPOT.Hardware' (4.1.2821.0)Loading Deployment Assemblies.Assembly: MicroLiquidCrystal (1.1.0.0)Attaching deployed file. needs assembly 'Microsoft.SPOT.Native' (4.1.2821.0)   Assembly: SecretLabs.NETMF.Hardware.Netduino (4.2.1.0)Error: a3000000Attaching deployed file.Waiting for debug commands...   Assembly: LCD_Buttons (1.0.0.0)Attaching deployed file.   Assembly: MicroLiquidCrystal (1.1.0.0)Attaching deployed file.   Assembly: SecretLabs.NETMF.Hardware (4.2.0.0)Resolving.Pinging... TinyCLRPinging... TinyCLR

In Topic: Help with 128*64 OLED display

10 January 2013 - 01:39 PM

At first glance you could try using the I2C way, because the SPI protocol requires a 9-bit transfer which is not supported.

The I2C should be feasible, although not so fast to play animations or similar.

Bear in mind to add a couple of pull-up resistors (e.g. 5k Ohms) to +3.3V.

 

Oh...I wouldn't throw it away: although an LCD won't give much satisfaction with a Netduino, you could have fun by adding an Arduino. At that point, the Arduino makes the "dirty job" and the Netduino the elegant one!

Cheers

 

 

Thanks, 

 

i will look at the i2C way  ;)

You mention pull-up resistors, on which pins?

 

Last Monday i order a Arduino, it seemed fun to combine the 2 boards into 1 project


In Topic: Help with 128*64 OLED display

10 January 2013 - 08:26 AM

I contacted the seller,

 

he sent me this link today:
http://www.divshare....ad/18744334-626

 

 

i'm using the standard Netduino (framework 4.2)


In Topic: Help with 128*64 OLED display

09 January 2013 - 10:46 PM

Hello

 

a couple of weeks ago i bouth this little display:

 

 

 

Posted Image

 

pin1: GND    = Ground

pin2: V         = 5V?

pin3: D0       = CLK

pin4: D1       = MISO

pin5: RST     = Reset

pin6: DC       = Data / Command

pin7: CS       = Chip Select (CSN)

 

only one problem, i cant get it to work
i have tried it for a couple of days now, and im at the point of throwing it out of the window :angry:

 

i have tried a couple of projects as base, but can't even find a good diagram for wireing.

 

 

does anyone have experience with this LCD??

 

more info:
http://item.taobao.c...&id=12825164303

 

 

Bram van Deventer


home    hardware    projects    downloads    community    where to buy    contact Copyright © 2016 Wilderness Labs Inc.  |  Legal   |   CC BY-SA
This webpage is licensed under a Creative Commons Attribution-ShareAlike License.