As the topic states...
Netduino 2 Mini planned?
#1
Posted 23 January 2013 - 10:27 PM
#2
Posted 23 January 2013 - 11:24 PM
Hi FMode, There are no immediate plans for a Netduino Mini 2. It's really hard to pack that much NETMF power into such a small module (especially with edge pins).
We can re-explore that later this year...but for now we're focused on new features for Netduino mainboards and more accessories to help bring your projects to life. Chris
#3
Posted 24 January 2013 - 08:01 AM
I'm a great fan of the mini, its so robust and versatile while yet tiny.
I too would love to see an upgraded mini. In the meantime there's always the Cerb40 over at GHI:
http://www.ghielectr...log/product/353
Just like the N+ and N2, it's based around the STM32F4 @ 168Mhz with FPU, 1MB FLASH and 192KB RAM, 36 GPIO and USB host. It's a little bit bigger than the N mini but still rather small and got on board USB device which omits the need for an FTDI cable or similar. Optionally, you can also fit a 32.768 kHz crystal to enable the real time clock. Yes, I like that one too :-)
@Chris: Sorry for mentioning products from another vendor but you have to admit it's a pretty nice board.
#4
Posted 24 January 2013 - 02:36 PM
#5
Posted 24 January 2013 - 10:36 PM
#6
Posted 24 January 2013 - 11:43 PM
now when talking about power consumption, my mini whith some code running is using roughtly 100ma - 110ma, thats around the same that an stm32f4 uses.
id like to see such thing as netduino-mini 40pin version
please just no f2, use a f4 if you design one -.-
edit:
nice features:
rtc enabled
no 12v rs-232 (eeks)
maybe the plus2 enc drivers included so you only need to hook one up
digital to analog pins exposed and useable
#7
Posted 25 January 2013 - 08:45 AM
Could 't agree with you more. I love the mini for all the reasons you mentioned and more.
Another mini-lover
I'm a big fan of the mini, especially since it uses the basic stamp format for which I have IC feet. Makes them easier to hotswap and look like real powerful chips.
My .NETMF projects: .NETMF Toolbox / Gadgeteer Light / Some PCB designs
#8
Posted 29 January 2013 - 03:10 AM
I'm a total mini lover. Please keep making it...
#9
Posted 29 January 2013 - 07:01 PM
#10
Posted 18 February 2013 - 08:36 PM
I'd just like to express my support for a Netduino Mini 2 around the STM32F processor. I wouldn't even mind if it was a 40-pin version like the Cerb40.
#11
Posted 08 March 2013 - 01:20 AM
Another fan of the mini. The current version should be proudly posted on the hardware page, even if there are no plans to create another version. It will help you sell more of them... which may help you decide to rev them.
#12
Posted 08 March 2013 - 01:47 PM
Definitely![...] The current version should be proudly posted on the hardware page [...]
#13
Posted 10 March 2013 - 04:15 PM
yep, also love it.
I ordered a FEZ Cerb40 as an alternative (especially like the 3 uart's on such a small board) but would love to see a new mini revision.
#14
Posted 08 April 2013 - 08:49 PM
I also like the mini. onboard rtc would be great. Maybe another 10 or so gpio's, some that are current drain. slightly larger module is ok. the speed is ok for my project.
#15
Posted 03 May 2013 - 12:15 AM
Netduino Mini FTW!
I'll love to see its successor!
#16
Posted 03 May 2013 - 10:32 PM
yep, also love it.
I ordered a FEZ Cerb40 as an alternative (especially like the 3 uart's on such a small board) but would love to see a new mini revision.
I got a couple of those about a year ago, mounted the RTC crystal and everything. For some reason I haven't really used them yet, I guess I'm too much in love with the current mini
#17
Posted 07 May 2013 - 04:13 AM
I would also be interested in a Netduino Mini 2 (love the minis). I would suggest changing the COM2 to a TTL though., and adding a 3v regulator. Dont some of the new chips have an FTDI logic in them as well? A built in USB would be nice as well. Just my 2 cents
#18
Posted 13 July 2013 - 02:59 AM
Form factor settling. In its present form it is some what difficult install into an ordinary breadboard.
Whereas the current form factor works for installing it into a BS2 board, I don't normally use them. Most of them are moving from physical serial (RS232 style) input, they are moving towards USB as input. In fact they sell a board which they call a stampdunio, its a BS2 board in the shape of a 'dunio, much like the regular ones here. I imagine the schematic is available on the site.
Doctor Who
"This signature does not exist!"
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users