Is the Netduino 3 layout open source as well? - General Discussion - Netduino Forums
   
Netduino home hardware projects downloads community

Jump to content


The Netduino forums have been replaced by new forums at community.wildernesslabs.co. This site has been preserved for archival purposes only and the ability to make new accounts or posts has been turned off.
Photo

Is the Netduino 3 layout open source as well?

Netduino 3

  • Please log in to reply
8 replies to this topic

#1 joel@emscable.com

joel@emscable.com

    New Member

  • Members
  • Pip
  • 8 posts

Posted 15 December 2016 - 10:21 PM

I have a customer who want to make their own board based off of the netduino 3 using the same firmware.

Since the layout files are not available for download, I wanted to get feedback on this before replying to my customer.

 



#2 joel@emscable.com

joel@emscable.com

    New Member

  • Members
  • Pip
  • 8 posts

Posted 19 December 2016 - 07:42 PM

Can the Netduino 3 board gerbers and or PCB file be downloaded?

 

Also is the firmware available to load into a blank ST Micro MCU to get a new board up and running the same as a NetDuino 3?

 

How open source is the Netduino 3?

 

ALL of this is based off of my customers concern that the Netduino 3 board may be going obsolete or no longer able to buy in the near future with the same footprint.



#3 bryancostanich

bryancostanich

    Advanced Member

  • Administrators
  • 62 posts

Posted 31 December 2016 - 12:36 AM

I believe that the firmware would be the same, yes. As long as you have the same USB wiring.

 

N3 is very open source. you can find all the board and schematic files here: http://www.netduino.com/downloads/



#4 joel@emscable.com

joel@emscable.com

    New Member

  • Members
  • Pip
  • 8 posts

Posted 04 January 2017 - 06:56 PM

What is required to program a new board that has a blank STM32F427 on it with the firmware to get it upto the Netduino 3 setup?

 

If it requires a in circuit jtag programmer... do you have a recommendation?



#5 joel@emscable.com

joel@emscable.com

    New Member

  • Members
  • Pip
  • 8 posts

Posted 04 January 2017 - 10:48 PM

Does anyone have the netduino 3 sources files?  They are not listed on the website.  Also what is the development software used to compile the source files and load them into the MCU?  What is the prefered programmer for this?



#6 bryancostanich

bryancostanich

    Advanced Member

  • Administrators
  • 62 posts

Posted 06 January 2017 - 06:02 AM

Joel; GHI has written a fantastic tutorial that answers all that you ask: http://www.ghielectr...rting NETMF.pdf



#7 joel@emscable.com

joel@emscable.com

    New Member

  • Members
  • Pip
  • 8 posts

Posted 18 January 2017 - 01:40 PM

It would be helpful if someone could put the ASCII version of the PCB layout on the download page.  This would allow for them to be imported into other layout software.

 

Would also like to see the source files for the Netduino 3 on the download page as well.



#8 neslekkim

neslekkim

    Advanced Member

  • Members
  • PipPipPip
  • 350 posts
  • LocationOslo, Norway

Posted 08 February 2017 - 06:23 PM

Asked about this also for long ago, they ended up doing this, but I think its not complete for the netduino3

https://github.com/netduino/netmf


--
Asbjørn


#9 neslekkim

neslekkim

    Advanced Member

  • Members
  • PipPipPip
  • 350 posts
  • LocationOslo, Norway

Posted 08 February 2017 - 06:23 PM

Asked about this also for long ago, they ended up doing this, but I think its not complete for the netduino3

https://github.com/netduino/netmf


--
Asbjørn






Also tagged with one or more of these keywords: Netduino 3

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users

home    hardware    projects    downloads    community    where to buy    contact Copyright © 2016 Wilderness Labs Inc.  |  Legal   |   CC BY-SA
This webpage is licensed under a Creative Commons Attribution-ShareAlike License.